Starting up n tuning the Team infinity engine of ACME
September 3rd, 2010 | 
Author:
Many who bought ACME Racings RC cars wrote to me that they had troubles starting this Team infinity Engine with blue top heat sink. Also few complained they couldnt keep it running properly or tune it. Well here is the video for all those having troubles with team infinity engine for starting or tuning. Hope this will do the job n all those having troubles can start having fun with their cars. Comments feedback welcome at alishanmao@gmail.com. Don’t forget to check www.redcatracing.com, http , www.hobby-estore.com , http www.metacafe.com racing and www.youtube.com Cheers
Similar Posts:
- Tuning the ACME Warrior Buggy
- How to Tune Nitro Engine Version 2
- Understanding Carb n Tuning the Engine
- Tuning the Bug Crusher Team Infinity .18 How to tune a Nitro Engine
- RC Entry Level Setup Guide 8/9- Engine tuning
Posted in 
Tags:
Could u do a tunig vid 4 redcat racings shockwave cause I’m getting one.
Cheers
@fedmyfishplease watch my videos why engine revs right after starting and why engine quit when braking
nice vid dude.
i got this car. please tell me when i start my car the wheels spin straight away. even when pressing back on the controller doesn’t really slow them down. how do i stop this happening.
cheers
nice vid dude.
please tell me when i start my car the wheels spin straight away. even when pressing back on the controller doesn’t really slow them down. how do i stop this happening.
cheers
@Leaflite 20% or 30%
for a .18 engined cyclone pro, which fuel should i use?
@alishanmao ok, thanx m8. u are really helpful !
@PCRampagE go with 20%
when the pullstart is hard its only good, that means that u got a good compesion and hat good !
i got one question, i buyed a Team VTX with .26 engine.. what % of fuel should i use?
@kayagecee if its ACME car with team infinity engine then you have wasted your money. these engines and cars are crap only. Anyway, check your glow plug, make sure you prime engine right, not flood it, these shitty team infinity engine flood soon and get lean soon with over heating problems too.
Hi there, I’m a noob with nitro cars and need some help after messingup the carb settings.
I did exactly what is shown in the vid, but the engine still won’t start. What am I doing wrong?
Hi there, I have tried to setup the carb according the vid. But the engine still does not start, what am i doing wrong. I have checked the igniter, primed the engine adjusted the carb settings. please help
@lukereidy100 LOL You snap the aerial off? man you should not. That is why you loose signals.
@lukereidy100 Better do not drive. replace the axle
1 outher thing is my back wheel on my nitro rampage the wheel is bent i think it needs a new hex i dont no how to replace it so the thing i whant to no is will it be ok to drive when i drive it you can see its a bit bent but it seems ok what do you think thanks for all your help
this is the problems ive been having with my rc nitro rampage car is i think its called a receiver box. its a black box with a ariel coming off the end and it has three ports for three wires to go in it. so i snapped the ariel off it and i taped it up and it done rubbish losing signal all the time so i changed it and put my condor receiver in it would it be ok it seems to be working fine and i changed the Crystal in it so i can use acme remote and it all seems ok is it ok to use thanks.
@lukereidy100 yes you can. maybe a bit of linkage setting needed
could i put my sh nitro engine in this car would i need to swap the linkages around.
@alishanmao yes
@Croky92 did you try to change the One way bearing?
hey again m8, oki it happend AGAIN !?!?! it still slips -.- we see it works well after cleaning the one way bearing, but then after iv run it its just slips again? how come its getting like that ??
@JeffHardyFan6334 yes you can
can i put this engine on my 1/10 buggy speedy tiger please reply
@alishanmao is redcat better than hsp because they are exactly the same
are yer i got one its good